Faculty of Engineering, Chemical & Process Engineering
Permanent URI for this communityhttp://192.248.9.226/handle/123/26
Browse
Browsing Faculty of Engineering, Chemical & Process Engineering by Author "Amarasinghe BMWPK"
Now showing 1 - 2 of 2
- Results Per Page
- Sort Options
- item: Thesis-Full-textHeat and mass transfer analysis in a spouted bed dryer coupled with a cyclone for pepper drying(2020) Jayatunga GK; Amarasinghe BMWPKThis thesis outlines the analysis of heat and mass transfer process of drying of black_pepper in a spouted bed coupled with a cyclone separator. Black pepper is a widely used spice and is well-known for its pungency and aroma. Experiments conducted with wetted black pepper reveals that conventional spouted bed has the higher drying rate, higher moisture diffusivity, lower drying time and lower activation energy compared to those of spouted_beds equipped with porous_draft tube and non-porous draft tube. Therefore, the conventional spouted bed was used to conduct the experiments to achieve the objectives of the study since it was identified as the optimum configuration of the spouted bed. Spouting behaviour of raw black pepper was studied in the conventional spouted bed. The minimum spouting velocities of particular bed heights at ambient temperature were determined. Minimum spouting velocity of raw black pepper in the conventional spouted_bed versus static bed height was correlated to a power form of function and the exponent of static bed height was 0.67. The effect of operational conditions; drying air temperature, air velocity and static bed height on drying kinetics of raw black pepper was analysed. The higher values of moisture removal rates were achieved when the dryer was operated with moderately high air temperatures, high air flow rates and shallow beds. Drying kinetic data of raw black pepper in the conventional spouted bed shows only falling rate periods. Effective moisture diffusivity values increased with increasing drying air temperature. The highest effective moisture diffusivity of 2.03×10-10 m2/s was obtained at air temperature of 75 ᵒC. Activation energy for drying of raw black pepper in conventional spouted bed was 38.59 kJ/kmol. Specific energy consumption was calculated and the specific energy consumption values increased with increasing air velocity and decreased gradually with increasing the static bed height. Drying_kinetic data obtained from experiments were fitted to five thin_layer drying models. Results show that the Logarithmic model gives the best fit. In addition, four models were developed for black pepper drying in the conventional spouted bed by correlating drying constants and coefficients of Logarithmic model to stagnant bed height at specified temperatures; 45 ᵒC, 55 ᵒC, 65 ᵒC, and 75 ᵒC. Developed models can be used to estimate the drying time of black pepper in the conventional spouted bed dryer for given moisture reduction in the ranges of 0.14-0.22 m stagnant bed heights and in 2.37 m/s air velocity at specified temperatures. Essential_oil was extracted using hydro distillation from black pepper dried at five different drying conditions. The analysis of components by Gas Chromatography Mass Spectrometry technique shows that the black pepper essential oil comprised mainly monoterpenes and sesquiterpenes. Analysis of variance was conducted and the results show that variation of sesquiterpenes concentration in black_pepper essential oil was significant while variations of monoterpenes, oxygenated terpenes and caryophyllene concentration were non-significant in black pepper essential oil with drying air temperature. In addition, the variation of essential oil yield is statistically significant with drying air temperatures. 65 ᵒC drying air temperature provides consistent quality essential oil with high percentage of caryophyllene and higher oil yield. Heat transfer coefficients for black_pepper drying in the conventional spouted dryer were estimated for different drying conditions of unsteady state drying of black pepper dried from initial moisture content to final moisture content of 15% dry basis. Heat transfer coefficient varied from 35-68 W/m2K for the conditions under the investigation. Dimensional analysis iii was carried out and important dimensionless numbers were identified. A correlation was developed for heat_transfer process as a function of dimensionless groups namely Reynolds number, Nusselt_number, Gukhman_number and static_bed height to particle_diameter with 0.791 of coefficient of determination. Heat transfer coefficients predicted from the developed correlation show a good agreement with the experimentally determined heat transfer coefficients.
- item: Thesis-Full-textSingle and binary adsorption of nickel and zinc ions from aqueous solutions using coirpith as the adsorbent(2020) Ranasinghe EN; Amarasinghe BMWPKThis study analysed the competitive adsorption of multicomponent systems onto coir pith, readily available and environmentally friendly adsorbent chosen for the study. The efficacy of unmodified coir pith as an adsorbent as well as its physical and chemical characteristics were studied to analyse single and binary systems of nickel and zinc adsorption onto coir pith as well as the effects of temperature, concentration, adsorbent dose and pH to determine the optimal conditions for adsorption. The equilibrium data for the single system adsorption of nickel and the single system adsorption of zinc at 30 °C was analysed using the Langmuir and Freundlich isotherm models while the multicomponent adsorption was analysed using the Langmuir, the Freundlich, the competitive Langmuir, the non-competitive Langmuir, the modified competitive Langmuir and the Langmuir Freundlich isotherm models. The single system adsorption data for both nickel and zinc fit the Freundlich model which showed the adsorption surface was heterogeneous. The multicomponent adsorption system data fit the Langmuir isotherm model the best which showed the adsorption surface formed a monolayer. Most adsorption occurs at a higher pH value. To decrease costs and possibility of metal hydroxide precipitation the adsorption should be carried out at a neutral pH. The kinetics of single system and binary system adsorption of nickel and zinc was studied using Lagergren pseudo first order model, pseudo second order model and the intraparticle diffusion model. The experimental data showed all of the systems could be described using pseudo second order model which shows adsorption occurs primarily through chemisorptions. In the single system the coir pith had a higher capacity for zinc than nickel. In the single system adsorption of nickel the adsorption increases with temperature which shows the adsorption of nickel is an endothermic process. In the zinc single systems the adsorption decreased when temperature increased which shows zinc adsorption is an exothermic process. In the adsorption capacity in the binary system is less than either of the single systems which prove in the presence of competitive species metal ion adsorption is hindered. The data was analysed using the Intraparticle diffusion model which showed intraparticle diffusion in the nickel single system and in the zinc single system at 30 °C but little to no intraparticle diffusion at higher temperatures or in the multicomponent system The FTIR analysis of the surface of coir pith before and after adsorption shows that adsorption decreases the presence of hydroxyl (-OH) bonds. This confirms the results of the kinetic analysis that the adsorption is a chemical process which breaks and forms bonds with the functional groups on the coir pith surface. The metal ion forms a complex with the polar surface functional groups during adsorption and the metal ion remains bonded to the surface even when the adsorbent is removed from the water and dried. This confirms coir pith is an effective adsorbent for the removal of heavy metals from aqueous solution. To optimise multicomponent adsorption of nickel and zinc it should be carried out close to 30 °C in a solution of neutral pH and allowed to reach equilibrium.